milamu

EyeTV-T2 not working

Recommended Posts

Nach dem update auf 7516 zeigen die ZDF-Kanäle tatsächlich bewegte Bilder. Das ist ein Fortschritt - traurig, das sagen zu müssen!

Aber: Das Bild ist immer noch abgehackt! eyetv ist damit nach wie vor nicht verwendbar!

Liebes geniatech-team: your work is not yet done - please go on!!!

 

Share this post


Link to post
Share on other sites

After 7516 update ZDF mux is much better here in Berlin. But now ARD mux with Das Erste, RBB, NDR. HR tends to stutter after a while, unusable.

Another suggestion:
It is possible to play EyeTV T2 content via plugin in VLC (unfortunately without timeshift). VLC uses much less processor power and energy than EyeTV. So there is still overall optimization in processor use possible.

Share this post


Link to post
Share on other sites

Hi,

 

just downloaded the 7516 and made a sender search run. At first glance better, expecially the ZDF Neo and ZDF Info don't stop the picture after 10 seconds  like before.

3Sat in bad quality, the picture is clear, but stops every few second.

Have programmed Tagesschau this evening at 8 pm - in the past it was not watchable - audio not in sync. Let's see.

Funny note: when I played the mpg (of ARD HD)  file with VLC, the audio was in sync, so the recording seemed okay.

I'm happy about every improvement - because the stick was not that cheap.

Keep up the good work at geniatech!

Best regards

Volker

 

  • Like 1

Share this post


Link to post
Share on other sites
On 9.4.2017 at 8:14 PM, Mike said:

Hi,

you need to download a special version of EyeTV 3 here: https://www.geniatech.eu/eyetv/de/software/ or here Download: EyeTV 3.6.9 (7514). Your old code should be working fine. 7514 should show your new device. I had experienced the same problem. Anyway, the new software is full of bugs.

Thank you Mike, that's exactly the way to get it listed. Thumbs up.

Share this post


Link to post
Share on other sites
On 12.4.2017 at 5:22 PM, Mikyesun said:

eyetv 3.6.9 (7516) DVB-T2 HD HEVC – Update //-> Download Eytev 3 Version 3.6.9 (7516) HEVC 

Thank you. This forum is the only way to get proper information about what`s going on.

I loaded the latest updated today, and the troubles I've had with the previous version seem to be gone. Sound and picture are now synchronized, which was the biggest problem so far. Stability seems to be okay. Will see...

There is still plenty of way to go to get dvb-t2 implemented as good as dvb-t

Share this post


Link to post
Share on other sites

Guten Morgen - ja - wir sind noch lange nicht fertig - das Build (7517) ist auf dem Weg, ich denke das wir das im Laufe des Tages releasen können/ werden, bringt noch einmal einen wesentlichen Performance - Schub - wir haben aktuell keinen Schluckauf (stuttering) festgestellt, läuft jetzt alles sehr flüssig und CPU Last ist noch weiter runter. 

Anmerkung: wir haben festgestellt (TV, STB und Eyetv) das manchmal beim ARD e.g. das Erste HD, der Ton nur eine Tonspur enthält (Musik etc..) und keine Sprache, liegt möglicher an der Ausstrahlung und den Inhalten und wie encodiert wird, im diesem Fall unter Ton / umschalten auf andere Sprache, oder einmal eyetv beenden und eyetv 3 neustarten, bitte hierzu Feedback...,

wer will kann vorab eine Blick darauf werden, https://www.sendspace.com/file/rojgg8 (build 7516-CDR<17) - ansonsten wie gehabt am späten Nachmittag https://www.geniatech.eu/eyetv/de/software/ hier download / installieren.


Good Morning - yes - we are not ready yet - the software build (7517) is on its way, I think we will / can release it today, it will give another performance boost and decrease the load of the CPU, we have no stuttering (Schluckauf) anymore - even on a i5 / 1,6 GHz / 8GB Memory.

Remarks: we found a a audio issue (TV, STB, Eyetv) that sometime at the ARD Portfolio e..g Das Erste HD, only one Audio Spur is playing (Music, etc) and no Voice, this seems to be related to the used broadcasting, encoder and the content, if happen please switch audio to AAC other/unknown language, or close eyetv and restart eyetv, in any case feedback is highly appreciated. 

for early birds - who like to try https://www.sendspace.com/file/rojgg8 (build 7516-CDR<17) - any other later today as usual https://www.geniatech.eu/eyetv/de/software/ download / install.

österliche Grüsse / easterly regards

Mikyesun

ps. please see some testing with i5, 8GB, macOS Sierra  

i5-8MB-ARTEHD_20170415_2.jpg

i5-8MB-ARTEHD_20170415_2.jpg

Share this post


Link to post
Share on other sites

Hi,

 

I'm downloading now.

With 3.6.9 (7516) even on my Mac Mini with  3GHz  i7 more than 100% CPU for eyetv, see first screenshot from 17:29. And the fan is working heavyly.

 

With the newest release (7517) the % CPU  stays under 100, from 70 to 90 I would say, screenshot from 17:38 shows

 

Looks like a big step forward.

 

Best regards

Volker

 

 

Bildschirmfoto_2017-04-15_um_17_29_45.png

Bildschirmfoto 2017-04-15 um 17.38.38.png

Share this post


Link to post
Share on other sites
5 minutes ago, Mikyesun said:

@Volker, thanks for feedback, please have a check for the audio at the Das Erste HD... , work correctly?

At the moment during the "Sportschau", there are two audio channels. "AAC Deutsch" is very muted, the second one "AAC Unbekannte Sprache" has the normal level.

Both are the same ...

 

Edit: I have restartet eyeTV3, but it remains with two channels.

Bildschirmfoto 2017-04-15 um 19.33.10.png

Edited by experiment466

Share this post


Link to post
Share on other sites
1 minute ago, experiment466 said:

At the moment during the "Sportschau", there are two audio channels. "AAC Deutsch" is very muted, the second one "AAC Unbekannte Sprache" has the normal level.

Both are the same ...

 

Edit: I have restartet eyeTV3, but it remains with two channels.

Bildschirmfoto 2017-04-15 um 19.33.10.png

yes, can confirm / check it live - that we also experience some time - it is not always so, depend on the content / and how encoded - kinda strange, we are in talks with the responsible

Share this post


Link to post
Share on other sites

Hallo Mikyesun,

mit der Version 7517 kann ich jetzt das erstmal vernünftig gewisse Kanäle anschauen.

Warum braucht aber z.B. OneHD weniger CPU-Leistung als DasErste HD?

 

Alle ZDF-Kanäle funktionieren überhaupt nicht! Kann das an meinem Standort liegen? (Raum München)

Danke und Grüsse,

Mike

Share this post


Link to post
Share on other sites
3 minutes ago, milamu said:

 

 

 

Alle ZDF-Kanäle funktionieren überhaupt nicht! Kann das an meinem Standort liegen? (Raum München)

 

 

 

Funktioniert hier hervorragend. Habe schon mit der "alten" Version einen ganzen Film auf ZDF geschaut, hat funktioniert.

Share this post


Link to post
Share on other sites
10 hours ago, milamu said:

Sorry, ZDF-Kanäle zeigen nach erneutem Sendersuchlauf Signal, aber teilweise stockend.

Mike

Hi Milamu, was hast du für ein System macOS? CPU?

Share this post


Link to post
Share on other sites

MacOS 10.11.6 - Quadcore i7 mit 2,8 GHz - 16 GB RAM

Nach dem Neustart heute früh musste ich den Stick erst wieder aus- und einstecken, um überhaupt ein Signal zu bekommen.

Bei den ZDF-Kanälen ist am schwersten, ein flüssiges Signal zu erreichen.

Würde eine aktive Zimmerantenne etwas bringen?

Danke, Mike

Share this post


Link to post
Share on other sites

Ja komisch, beide Werte sind immer auf 100%, egal welcher Sender, dann brauche ich wohl keine zusätzliche Antenne.

Was ich festgestellt habe: Ich habe einen Platz für die Antenne gefunden, an welchem die meisten Sender einigermassen laufen,

der war aber sehr schwer zu finden und ich darf die Antenne nicht einen Zentimeter verrutschen!

Mike

 

Share this post


Link to post
Share on other sites

7517 läuft schon besser. Aber immer noch nicht ganz stabil. Bei Arte HD und ARD HD gibt es immer wieder kurze Hänger im Bild.

Share this post


Link to post
Share on other sites

Die 7517 ist schon fast gut! Die Abstürze scheinen jetzt behoben zu sein, auch ist jetzt Bild und Ton fast synchron. CPU bei etwa 75% (gegenüber 200%) ist auch besser. Kleine Aussetzer gibt es aber immer noch.

Wenn jetzt noch der Export nach Toast genauso problemlos funktionieren würde wie in der Version 2, dann wärt Ihr rehabilitiert!

Danke erst mal.

srswift

Edited by srswift
Typo

Share this post


Link to post
Share on other sites
8 hours ago, milamu said:

Ja komisch, beide Werte sind immer auf 100%, egal welcher Sender, dann brauche ich wohl keine zusätzliche Antenne.

Was ich festgestellt habe: Ich habe einen Platz für die Antenne gefunden, an welchem die meisten Sender einigermassen laufen,

der war aber sehr schwer zu finden und ich darf die Antenne nicht einen Zentimeter verrutschen!

Mike

 

ich denke es braucht eine kleine aktive(power) Antenne (indoor), wir haben das in verschiedenen Bundesländern / Ballungszentren festgestellt, die Ausleuchtung seitens der Ausstrahlung ist dann nicht optimal, und wenn weniger als 25 Bilder /sec ankommt - kommt es zu diesenm Schluckauf, ...gibt es schon für kleines Geld bei A. 

Share this post


Link to post
Share on other sites
7 hours ago, srswift said:

Die 7517 ist schon fast gut! Die Abstürze scheinen jetzt behoben zu sein, auch ist jetzt Bild und Ton fast synchron. CPU bei etwa 75% (gegenüber 200%) ist auch besser. Kleine Aussetzer gibt es aber immer noch.

Wenn jetzt noch der Export nach Toast genauso problemlos funktionieren würde wie in der Version 2, dann wärt Ihr rehabilitiert!

Danke erst mal.

srswift

genau darauf wollen wir uns nach diesem WE dann konzentrieren! 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.